Register My Garage Arcade V.I.P Members List Calendar Mark Forums Read
Go Back   my6thgen.org - Maxima Forum > my6thgen.org - Very Useful Information > How To's & DIY Mods > Suspension, Handling & Brakes

Reply
ExclamationThis thread is more than 150+ days old. If you still feel it is necessary to bump this thread, you have the permission to do so. Please click the checkbox below and post your reply.
 
Thread Tools
Old 01-30-2011, 07:13 PM   Thread Starter #1
Wheel/Tire Master

my6thgen.org Profile Info.
 
KCMAXX's Avatar
 
Join Date: Feb 2010
Official Member #: 108
Last Online: 07-25-2018 11:34 AM
Posts: 1,280

Reputation Level: 24
KCMAXX will become famous soon enoughKCMAXX will become famous soon enough

Participation Level: 0%
Activity: 0% Activity: 0% Activity: 0%

My Awards:
Banner of The Month  


/ Point Value: 10

V.I.P Member  


/ Point Value: 15

Spotlight Ride Of The Month  


/ Point Value: 5

Honorable Ride  


/ Point Value: 5

Default How to Rebuild (Z32) 300ZX Calipers

Found this on another forum and thought it would make a great sticky.

I know quite a few of you are, or have ran the Z32 BBK setup and after doing some homework I plan on trying it too.

LINK http://zmods.org/index.php?page=caliper_rebuild









Article Date: 06-21-08
Author: TC
Mod Class: Z32 All Models
Mod Type: Performance & Aesthetics
Article Origin: www.zmods.org
Difficulty Level:5(Scale of 1 to 10. 1 being extremely easy, 10 being extremely difficult.)
Estimated Time to Complete: Approx 2 hours per caliper after removal from the car. 48 hours to allow paint to cure before reinstalling.




Tools Required:

- Z32 front caliper rebuild kit
- 14MM Socket & ratchet
- Torque wrench
- Bench Vice
- Air Compressor
- Fine tipped awl
- Bench grinder with a wire wheel
- 2 cans of brake cleaner
- Acetone or lacquer thinner
- 2 cans of high temperature paint in the color of your choice
- High temperature clearcoat (optional, but recommended)
- Set of Speed Bleeders (optional, but recommended)
- Set of stainless steel brake lines (optional, but recommended)
- 2 quarts of brake fluid, brand of your preference



!!!WARNING!!! - This task can be a little tricky, so if you don't think you're up for the job, DO NOT ATTEMPT THIS!! Brakes are nothing to fool around with if you're not completely sure of what you're doing!! A mistake could land you in the hospital or morgue, and your car in the junkyard!! If you have little or no experience with brake work, forget you ever saw this writeup, and let a professional handle this job!!
I also recommend purchasing a set of core calipers off a parts car to do this on, as this procedure is time consuming. It will take a few days to do it right and allow the paint to cure, in which time your car will be out of commission, which is not an option if your Z is a daily driver. Its a lot easier to do this to some spare/core calipers, that way the brake lines aren't left open very long, and you can still drive your car while working on this. This is also a perfect time to upgrade from the scrawny 26mm calipers if you have an early 1990 model NA. When you're finished, you can resell your original calipers and recoup your money spent on the rebuilder set you bought.



With the above out of the way, now the fun begins!!
These are a set of 30mm aluminum calipers I pulled off a 1991 Twin Turbo parts car. They were high mileage, and had definitely seen better days.....until now!!


Click the image to open in full size.


Click the image to open in full size.



Basic Preparation for the build


Step 1:
The first thing you want to do is remove the pads and all the pad retention hardware. If you're reusing your old pads and not replacing them with new ones, you need to mark their orientation!! This is VERY important!! They need to go back on in the same location they came off!

Step 2:
Now that the pads and their hardware is out of the way, you now want to remove the rubber dust boots and retainer rings from the caliper pistons. Use the fine tipped awl and simply pop the metal ring off. The boot may come off with it. If it doesn't, just grab hold of it and pull, it will come off easily. You may discard these items in the trash FOR THE FRONT BRAKES ONLY, they will not be reused. The rebuild kit contains new replacements for the front brakes. You MUST SAVE the dust boots and O rings for the rear calipers!! Be VERY careful not to puncture the dust boots with the awl during removal on your rear calipers!!! The rear rebuild kits are NLA (no longer available) from Nissan!! On this note, they VERY VERY rarely ever fail, so this is nothing to worry about, you can reuse the O rings and dust boots without fear! When you remove the O rings and dust boots from the rear calipers, simply inspect them for damage. Damage you want to look for will be torn dust boots or damaged O rings (signs of leakage, cracks or chunks missing). It's not likely you'll find any. If for some reason you do, you'll need to replace that caliper.


Removing the pistons


The pistons now need to be removed from the caliper. This next sequence can be a bit tricky, especially if you have a sticky piston. A stuck piston is not too common, but it can happen. The pistons should come out fairly easily with the aid of an air compressor. If the piston is seized, the caliper may need to be replaced.

Step 1a:
Place a 2X4 up the middle of the caliper, between the pistons. Then place your air hose with a small nozzle chuck attached over the line fitting on the back of the caliper. Make sure the bleeder valve is installed and tight. Get yourself into position, making sure your fingers are NOWHERE NEAR the pistons!!! When you shoot the air into the caliper, the pistons will come out with some velocity! If your fingers are in the way, it can definitely cause injury!! When in position, give it a shot of air. The pistons will start to come out and converge on the 2X4. If any one comes completely out, leaving other still seated, slide it back in just enough to reseal, and shim the opposite side of it with thin wooden shims to keep it in its cylinder, allowing the others to come out.


Click the image to open in full size.


Click the image to open in full size.

Step 1b:
On the rear calipers, use the same technique, just use a thinner piece of wood. I used a piece of 3/4" plywood, it worked fine.


Step 2:
Once all the pistons are protruding from the caliper like the ones on the left in the picture above, they should pop out with little effort. If they're still too tight to pull by hand, you may use some large pliers. If you need to use pliers, grab the outer lip that the dust seal rests in!!!! DO NOT GRAB THE PISTON SIDES!! If you scratch or score it, the piston is ruined, as this will cause leaks!!

Step 3:
Now that all the pistons are out, you want to remove the "O" rings from the cylinders. Use your awl and carefully slide it between the ring and the slot, and raise up on the O ring. BE VERY CAREFUL NOT TO DIG INTO OR SCRATCH THE O-RING SEAT!! Again, this will cause irreparable damage, resulting in a leaky caliper!! When you're all done, this is what you should have:


Click the image to open in full size.


Splitting the caliper halves
In this sequence, we will be splitting the two caliper halves apart.

Step 1:
Place the caliper in your bench vise, and snug it down.

Step 2:
Using a 14MM socket & ratchet, loosen all 4 of the bolts. Once all 4 are loosened, go ahead and remove them from the caliper. Make sure you have a hold of the caliper half that's not in the vise, as when the bolts are removed, it may fall.

Click the image to open in full size.

Step 3:
Separate the halves, paying VERY close attention to two small O rings between the halves!!! They may fall to the floor or stick to the caliper. DO NOT LOSE THESE!! The kit does NOT include replacements for them, so these need to be kept safe for reuse during reassembly!!

Click the image to open in full size.


Click the image to open in full size.


Click the image to open in full size.


Chemical cleaning the calipers
Ok, this sequence is chemical washing of the caliper. This is where those cans of brake cleaner will be used. I did this outside, as it can be messy.

Step 1:
You want to douche (< heh) the caliper halves VERY thoroughly!! Make sure you get the fluid journals and the cylinders clean of all fluid and dirt, same with the exterior. I recommend wearing rubber gloves when doing this, as the brake cleaner can irritate your skin, and you WILL get some on your hands!! I have tough skin when it comes to things like this, and I'll admit, this stuff bothered me.

Step 2:
Let them dry, it won't take long, the cleaner evaporates fast. When done, they should look similar to this:


Click the image to open in full size.


Click the image to open in full size.

Wire wheel the calipers and hardware
This sequence is also another self explanatory one. You want to wire wheel all the embedded and caked on brake dust off. I strongly recommend wearing a respirator or dust mask when doing this!! Brake dust is contains asbestos. Not something you want to be inhaling!

Step 1:
Run the wire wheel over all accessible surfaces of the halves. You want to get into all the crevices, removing as much of the dust as you can. DO NOT allow the wire wheel to get into the cylinders!!! Also, do not wheel the mating surfaces where the halves join. Make sure the O ring seats are clean and free of debris, but don't wire wheel them if you can help it!!

Step 2:
Wire wheel the pad retention hardware and the 4 bolts as well. On the bolts, make sure you wheel off any rust or corrosion on them. Make sure you get all the crud and brake dust off the bolt heads, or this may cause problems later with the paint.
BEFORE:

Click the image to open in full size.

After:

Click the image to open in full size.

Calipers AFTER:

Click the image to open in full size.


Click the image to open in full size.

Step 3:
You now want to reunite the two halves. Put the front half in the vise. Before reuniting the halves, you may want to give the halves a blast with compressed air, just to make sure you left no dust in anything.

Step 4: <-- VERY IMPORTANT!! Don't skip this step!!
Place the O rings in their seats.

Step 5:
Place the back half onto the front half, making sure the O rings don't shift around or move. Insert the bolts, holding the halves together with your hand, not allowing them to shift around. Hand tighten the 4 bolts.

Step 6:
Torque the bolts to 60 ft lbs.


Click the image to open in full size.

Preparing for paint
In this sequence, you want to mask off things that you don't want paint in.

Step 1:
Mask off all of the cylinders, including the outer lips.

Step 2:
Place a small piece of masking tape over the front and back of the bolt holes. You don't want paint in the threads.

Step 3:
Place something in the line hole. I used an old bleeder I had. If you use a bleeder, you'll have to first grind the tip off it to allow it to fit. Also, make sure it's free of any oil or brake fluid.


Click the image to open in full size.

Click the image to open in full size.

Click the image to open in full size.

Step 4:
You now want to take a rag and wet it good with acetone or lacquer thinner. Wipe down the whole caliper with the soaked rag. This will remove any residual contaminants you may have gotten on the caliper from handling it after the chemical cleaning and the wire wheel cleaning. After wiping it down thoroughly, do not touch it with your bare hands again!! This is the final paint prep step before you actually spray them. If you get oil from your skin on them, the paint may not stick in those places.

Step 5:
Rig hangers to hold the calipers for painting. Do not set them on flat surfaces, you won't be able to get the underside, and it will definitely show in the end!! When making your hangers, set them so you have 360 degree access around them, so you can coat them evenly.

Click the image to open in full size.

Click the image to open in full size.

Painting your calipers
This is it!! This sequence covers spraying the base coat on the calipers. I used Duplicolor's high temp flat black as a base coat. This paint requires no primer, and can withstand temperatures up to 1200 degrees!

Step 1:
Follow the directions on the paint can, as that's the best way to start. Lightly coat the calipers the first couple coats, letting it tack up for a few minutes between coats.

Click the image to open in full size.

Step 2:
After two or three thin coats have been applied, start making the coats thicker. I typically use five or six coats of base on a caliper, this makes for a smooth yet robust coating. 2~3 thin coats, and 2~3 thicker coats. After your last coat, your calipers will look something like this (Yes, that is black. The paint is wet, and the flash distorts it a little. This is normal):

Click the image to open in full size.

Click the image to open in full size.

Click the image to open in full size.

Click the image to open in full size.

Step 3:
Allow the calipers to hang and dry for 24 hours.


Blocking the raised letters
This sequence will remove the paint from the raised letters, If you want the letters the same color as the calipers, you may skip this sequence.

Step 1:
You'll need a sheet of 100 grit sandpaper and a sanding block. I used a scrap piece of a 3/4" plywood with a flat surface. It was the perfect width to cover the lettering, but not overlap the rest of the caliper too much. This is helpful for avoiding acidents.

Click the image to open in full size.

Click the image to open in full size.

Step 2:
Wrap a small piece of the sandpaper around the block, making sure its pulled snug, so the paper won't slip.

Click the image to open in full size.

Step 3a:
Sand the lettering side to side until all the paint and texture is gone. You're finished when you've got a sharp and clean brushed look.

Click the image to open in full size.

Click the image to open in full size.

Step 3b:
On the rear calipers, the letters are smaller and not raised as high as the fronts. Use extreme caution not to angle the block, or you'll end up having to touch up or re-shoot the entire caliper!!!

Step 4:
When you're done, hang them back up, its time to clearcoat them.


Applying the clearcoat
This is done similar to the paint process. I used Duplicolor wheel clear, which is high temp.

Step 1:
Apply several thin coats, allowing it to tack up between coats.

Step 2:
Apply several thicker coats, again, allowing it to tack between coats. If when applying the thicker coats, using the Duplicolor wheel clear, you may notice a white milky appearance in the coating. This is nothing to be alarmed about, it will clear up as the coating begins to cure.

Click the image to open in full size.

Click the image to open in full size.

Click the image to open in full size.

Click the image to open in full size.

Click the image to open in full size.

Click the image to open in full size.

Click the image to open in full size.

Click the image to open in full size.

Step 3:
Allow them to dry overnight before handing them. I recommend letting them sit a couple days before reinstalling, to insure it's thoroughly dried.

Step 4:
After they're dried, remove all the tape, old bleeder valve, and whatever you had covering the brake line opening.


Reassembly
This one is also very cut and dry. Simply reassemble everything the opposite of how you took it apart, which is outlined earlier in the writeup.

Step 1:
Clean the pistons thoroughly, removing fluid, dirt, and gunk. Just use a rag and give them a good wipe down.

Step 2a - Front caliper O ring reinstall:
The new O rings will have grease on them. Do not wipe this off! Slide the O ring into its seat, making sure that its in there uniform. They will twist up easily, so make sure it doesn't do that. You'll know it if it does, you'll never get the piston back in!

Step 2b - Rear caliper O ring reinstall:
Since these are the old ones being reused, wipe them down to clean any dirt and fluid off of them. In your rebuild kit for the front calipers, you'll notice a packet of brake grease. Use a little of this on the O rings to slick them up, and then reinstall them the same way outlined in step 2a.

Step 3:
Now it's time to reinstall the pistons. Use a little of the pink brake grease and lube the side of the piston. Start the piston into the cylinder, and slowly push it in. DO NOT PUSH THE PISTON ALL THE WAY IN!!!!!!!!!!! You need to leave them sticking out a little to reinstall the dust boot. If they're all the way back, its a pain to get the boot on!!

Step 4a - Reinstalling the dust boot:
Now put the dust boots on. On the rear calipers, you might want to clean them up with some brake cleaner first, to get the gunk off them. Place it over the piston, allowing the boot to seat itself in the groove on the piston. NOW, you can push the piston all the way back in!

Step 4b - Reinstalling the dust boot:
Once the piston is all the way back, massage the outer edge of the boot until you feel it slide over the lip on the cylinder and seat. Then take the retainer rings and put those back on. Simply pull the ring open at its seam, place it into the groove on the dust boot, and let go. it will snap right into place. Verify it is seated by looking at it all the way around.

Step 5:
Install your new speed bleeders if you elected for those, and tighten them down.


That's it!!! You're now ready to reinstall them on the car, and bleed them down! I hope you found this article useful!
__________________
Click the image to open in full size.
Click the image to open in full size.
REAR STRUT BARS F/S, PM FOR DETAILS
√ MY THREADS IN THE WHEELS/TIRES F/S SECTION

Last edited by KCMAXX; 01-30-2011 at 10:42 PM.
Likes: (3)
EddyMaxx (02-08-2011), Gearbox (01-31-2011), RAZ76 (02-10-2011)
KCMAXX is offline   Send a private message to KCMAXX Find more posts by KCMAXX Add KCMAXX to Your Friends list Reply With Quote top
Old 01-30-2011, 09:36 PM   #2
my6thgen.org Profile Info.
 
Hmax's Avatar
 
Join Date: Mar 2010
Official Member #: 158
Last Online: 05-10-2018 02:35 PM
Location: Da Bronx, NY
Posts: 5,926

Reputation Level: 32
Hmax will become famous soon enoughHmax will become famous soon enough

Participation Level: 0%
Activity: 0% Activity: 0% Activity: 0%

My Awards:
Most Valuable Poster (MVP)  


/ Point Value: 10

Active Member  


/ Point Value: 5

Default Re: HOW TO REBUILD Z32 CALIPERS

Great find definitely detailed
__________________
Originally Posted by hero782 View Post
Low & Slow!!! And I stop at potholes lol
Click the image to open in full size.

Want 12HP More?- CLICK HERE
Hmax is offline   Send a private message to Hmax Find more posts by Hmax Add Hmax to Your Friends list Reply With Quote top
Old 01-30-2011, 10:14 PM   #3
Premier Member
my6thgen.org Profile Info.
 
NiZMo1o1's Avatar
 
Join Date: May 2010
Official Member #: 211
Last Online: 10-20-2016 11:20 AM
Location: Wade County ! down in Sunny Florida
Posts: 5,222

Reputation Level: 42
NiZMo1o1 has a spectacular aura aboutNiZMo1o1 has a spectacular aura aboutNiZMo1o1 has a spectacular aura about

Participation Level: 20%
Activity: 20% Activity: 20% Activity: 20%

My Awards:
Supporting Family Member  


/ Point Value: 10

Member of the Month (M.O.T.M)  


/ Point Value: 10

Default Re: How to Rebuild Your 300zx Z32 Calipers

__________________
Click the image to open in full size.
Click the image to open in full size.
R.I.P. Kevin007www.EmeraldPerformance.com
NiZMo1o1 is offline   Send a private message to NiZMo1o1 Find more posts by NiZMo1o1 Add NiZMo1o1 to Your Friends list Reply With Quote top
Old 01-30-2011, 11:16 PM   #4
Official Member
my6thgen.org Profile Info.
 
Maxman's Avatar
 
Join Date: Jun 2010
Official Member #: 294
Last Online: 04-14-2013 11:01 PM
Location: Louisville, KY
Posts: 263

Reputation Level: 12
Maxman is on a distinguished road

Participation Level: 0%
Activity: 0% Activity: 0% Activity: 0%
Default Re: How to Rebuild (Z32) 300ZX Calipers

Wow, awesome find! but I think ill leave my breaks alone! As much as I like going fast I like stopping more, and if I tried that, well it might get sketchy
Maxman is offline   Send a private message to Maxman Find more posts by Maxman Add Maxman to Your Friends list Reply With Quote top
Old 01-30-2011, 11:32 PM   #5
my6thgen.org Profile Info.
 
EddyMaxx's Avatar
 
Join Date: Jan 2010
Official Member #: 1
Location: Bat-Brooklyn, NYC
Posts: 34,328

Reputation Level: 20
EddyMaxx is a splendid one to beholdEddyMaxx is a splendid one to beholdEddyMaxx is a splendid one to beholdEddyMaxx is a splendid one to beholdEddyMaxx is a splendid one to beholdEddyMaxx is a splendid one to beholdEddyMaxx is a splendid one to behold

Participation Level: 100%
Activity: 100% Activity: 100% Activity: 100%


Visit EddyMaxx's Facebook Visit EddyMaxx's PS3 Profile Visit EddyMaxx's YouTube
Default Re: How to Rebuild (Z32) 300ZX Calipers

Originally Posted by Maxman View Post
Wow, awesome find! but I think ill leave my breaks alone! As much as I like going fast I like stopping more, and if I tried that, well it might get sketchy
Good brakes aren't only about going fast.

Extra security when needed.
__________________
04' Nissan Maxima - [Supercharged w/ HR Swapped Motor & Fully Built Auto Trans]
98' Nissan Maxima - [VQ35DE 6-Speed Supercharged]

6thgen 2014 Build Thread
EddyMaxx is offline   Send a private message to EddyMaxx Find more posts by EddyMaxx Add EddyMaxx to Your Friends list Reply With Quote top
Old 01-30-2011, 11:34 PM   #6
Official Member
my6thgen.org Profile Info.
 
Maxman's Avatar
 
Join Date: Jun 2010
Official Member #: 294
Last Online: 04-14-2013 11:01 PM
Location: Louisville, KY
Posts: 263

Reputation Level: 12
Maxman is on a distinguished road

Participation Level: 0%
Activity: 0% Activity: 0% Activity: 0%
Default Re: How to Rebuild (Z32) 300ZX Calipers

Oh no i agree, I just figure id do more harm than good
Maxman is offline   Send a private message to Maxman Find more posts by Maxman Add Maxman to Your Friends list Reply With Quote top
Old 01-30-2011, 11:36 PM   #7
my6thgen.org Profile Info.
 
EddyMaxx's Avatar
 
Join Date: Jan 2010
Official Member #: 1
Location: Bat-Brooklyn, NYC
Posts: 34,328

Reputation Level: 20
EddyMaxx is a splendid one to beholdEddyMaxx is a splendid one to beholdEddyMaxx is a splendid one to beholdEddyMaxx is a splendid one to beholdEddyMaxx is a splendid one to beholdEddyMaxx is a splendid one to beholdEddyMaxx is a splendid one to behold

Participation Level: 100%
Activity: 100% Activity: 100% Activity: 100%


Visit EddyMaxx's Facebook Visit EddyMaxx's PS3 Profile Visit EddyMaxx's YouTube
Default Re: How to Rebuild (Z32) 300ZX Calipers

Got ya.
__________________
04' Nissan Maxima - [Supercharged w/ HR Swapped Motor & Fully Built Auto Trans]
98' Nissan Maxima - [VQ35DE 6-Speed Supercharged]

6thgen 2014 Build Thread
EddyMaxx is offline   Send a private message to EddyMaxx Find more posts by EddyMaxx Add EddyMaxx to Your Friends list Reply With Quote top
Old 01-31-2011, 07:40 AM   #8
my6thgen.org Profile Info.
 
Hmax's Avatar
 
Join Date: Mar 2010
Official Member #: 158
Last Online: 05-10-2018 02:35 PM
Location: Da Bronx, NY
Posts: 5,926

Reputation Level: 32
Hmax will become famous soon enoughHmax will become famous soon enough

Participation Level: 0%
Activity: 0% Activity: 0% Activity: 0%

My Awards:
Most Valuable Poster (MVP)  


/ Point Value: 10

Active Member  


/ Point Value: 5

Default Re: How to Rebuild (Z32) 300ZX Calipers

Eddy, this information is a bit sticky NO
__________________
Originally Posted by hero782 View Post
Low & Slow!!! And I stop at potholes lol
Click the image to open in full size.

Want 12HP More?- CLICK HERE
Hmax is offline   Send a private message to Hmax Find more posts by Hmax Add Hmax to Your Friends list Reply With Quote top
Old 01-31-2011, 09:42 AM   #9
my6thgen.org Profile Info.
 
EddyMaxx's Avatar
 
Join Date: Jan 2010
Official Member #: 1
Location: Bat-Brooklyn, NYC
Posts: 34,328

Reputation Level: 20
EddyMaxx is a splendid one to beholdEddyMaxx is a splendid one to beholdEddyMaxx is a splendid one to beholdEddyMaxx is a splendid one to beholdEddyMaxx is a splendid one to beholdEddyMaxx is a splendid one to beholdEddyMaxx is a splendid one to behold

Participation Level: 100%
Activity: 100% Activity: 100% Activity: 100%


Visit EddyMaxx's Facebook Visit EddyMaxx's PS3 Profile Visit EddyMaxx's YouTube
Default Re: How to Rebuild (Z32) 300ZX Calipers

Its been a sticky. Remem KC is a moderator. lol
__________________
04' Nissan Maxima - [Supercharged w/ HR Swapped Motor & Fully Built Auto Trans]
98' Nissan Maxima - [VQ35DE 6-Speed Supercharged]

6thgen 2014 Build Thread
EddyMaxx is offline   Send a private message to EddyMaxx Find more posts by EddyMaxx Add EddyMaxx to Your Friends list Reply With Quote top
Old 01-31-2011, 10:57 AM   #10
my6thgen.org Profile Info.
 
Hmax's Avatar
 
Join Date: Mar 2010
Official Member #: 158
Last Online: 05-10-2018 02:35 PM
Location: Da Bronx, NY
Posts: 5,926

Reputation Level: 32
Hmax will become famous soon enoughHmax will become famous soon enough

Participation Level: 0%
Activity: 0% Activity: 0% Activity: 0%

My Awards:
Most Valuable Poster (MVP)  


/ Point Value: 10

Active Member  


/ Point Value: 5

Default Re: How to Rebuild (Z32) 300ZX Calipers

I forgot he has da POWA
__________________
Originally Posted by hero782 View Post
Low & Slow!!! And I stop at potholes lol
Click the image to open in full size.

Want 12HP More?- CLICK HERE
Hmax is offline   Send a private message to Hmax Find more posts by Hmax Add Hmax to Your Friends list Reply With Quote top
Old 01-31-2011, 11:36 AM   #11
Senior Moderator
my6thgen.org Profile Info.
 
Chemax's Avatar
 
Join Date: Feb 2010
Official Member #: 140
Last Online: 10-04-2014 01:46 PM
Location: SATX
Posts: 11,313

Reputation Level: 51
Chemax has a spectacular aura aboutChemax has a spectacular aura about

Participation Level: 0%
Activity: 0% Activity: 0% Activity: 0%

My Awards:
Supporting Family Member  


/ Point Value: 10

Active Member  


/ Point Value: 5

Default Re: How to Rebuild (Z32) 300ZX Calipers

Damn. That makes me want to do some brakes on my car...
__________________
Click the image to open in full size.
We all have different ways of coping - I use sex and awesomeness.

mmm.... chorizo
-csiepka
Chemax is offline   Send a private message to Chemax Find more posts by Chemax Add Chemax to Your Friends list Reply With Quote top
Old 01-31-2011, 05:26 PM   #12
New Member
Donating Member
my6thgen.org Profile Info.
 
Gearbox's Avatar
 
Join Date: Feb 2010
Official Member #: 125
Last Online: 06-20-2013 07:27 AM
Location: Dallas, Texas
Posts: 259

Reputation Level: 12
Gearbox is on a distinguished road

Participation Level: 0%
Activity: 0% Activity: 0% Activity: 0%

My Awards:
Spotlight Ride Of The Month  


/ Point Value: 5

Default Re: How to Rebuild (Z32) 300ZX Calipers

great thread,.. i've been looking for a set at local junk yards to rebuild and put on the max.
__________________
Click the image to open in full size.
Click the image to open in full size.
Gearbox is offline   Send a private message to Gearbox Find more posts by Gearbox Add Gearbox to Your Friends list Reply With Quote top
Old 01-31-2011, 07:04 PM   Thread Starter #13
Wheel/Tire Master

my6thgen.org Profile Info.
 
KCMAXX's Avatar
 
Join Date: Feb 2010
Official Member #: 108
Last Online: 07-25-2018 11:34 AM
Posts: 1,280

Reputation Level: 24
KCMAXX will become famous soon enoughKCMAXX will become famous soon enough

Participation Level: 0%
Activity: 0% Activity: 0% Activity: 0%

My Awards:
Banner of The Month  


/ Point Value: 10

V.I.P Member  


/ Point Value: 15

Spotlight Ride Of The Month  


/ Point Value: 5

Honorable Ride  


/ Point Value: 5

Default Re: How to Rebuild (Z32) 300ZX Calipers

Originally Posted by Gearbox View Post
great thread,.. i've been looking for a set at local junk yards to rebuild and put on the max.
Most of the major auto parts stores carry (or can get) these calipers. I had Oriellys order a set for me, but they ended up being the cast iron ones.

I did find one co. who stocks the 30mm aluminum calipers but they HAVE to have the same for core trade in. With out the cores, they are $307 shipped for the pair, but they have been completely rebuilt and are ready for paint. The website also says partially packed so they may include pads as well.

I have a call to make in the morning reguarding a group buy kind of deal. I'll post more as it unfolds...
__________________
Click the image to open in full size.
Click the image to open in full size.
REAR STRUT BARS F/S, PM FOR DETAILS
√ MY THREADS IN THE WHEELS/TIRES F/S SECTION
KCMAXX is offline   Send a private message to KCMAXX Find more posts by KCMAXX Add KCMAXX to Your Friends list Reply With Quote top
Old 01-31-2011, 07:17 PM   #14
my6thgen.org Profile Info.
 
Hmax's Avatar
 
Join Date: Mar 2010
Official Member #: 158
Last Online: 05-10-2018 02:35 PM
Location: Da Bronx, NY
Posts: 5,926

Reputation Level: 32
Hmax will become famous soon enoughHmax will become famous soon enough

Participation Level: 0%
Activity: 0% Activity: 0% Activity: 0%

My Awards:
Most Valuable Poster (MVP)  


/ Point Value: 10

Active Member  


/ Point Value: 5

Default Re: How to Rebuild (Z32) 300ZX Calipers

DOES ANYONE HAVE A PART NUMBER FROM NISSAN FOR THESE????
I need this as I too am working to find these.
__________________
Originally Posted by hero782 View Post
Low & Slow!!! And I stop at potholes lol
Click the image to open in full size.

Want 12HP More?- CLICK HERE
Hmax is offline   Send a private message to Hmax Find more posts by Hmax Add Hmax to Your Friends list Reply With Quote top
Old 01-31-2011, 07:27 PM   Thread Starter #15
Wheel/Tire Master

my6thgen.org Profile Info.
 
KCMAXX's Avatar
 
Join Date: Feb 2010
Official Member #: 108
Last Online: 07-25-2018 11:34 AM
Posts: 1,280

Reputation Level: 24
KCMAXX will become famous soon enoughKCMAXX will become famous soon enough

Participation Level: 0%
Activity: 0% Activity: 0% Activity: 0%

My Awards:
Banner of The Month  


/ Point Value: 10

V.I.P Member  


/ Point Value: 15

Spotlight Ride Of The Month  


/ Point Value: 5

Honorable Ride  


/ Point Value: 5

Default Re: How to Rebuild (Z32) 300ZX Calipers

Originally Posted by Hmax View Post
DOES ANYONE HAVE A PART NUMBER FROM NISSAN FOR THESE????
I need this as I too am working to find these.

http://www.courtesyparts.com/kb_sear...82_883_982_983


I've found some Ham, give me some time. Actually, read the post above you... lol


you know I'll share.
__________________
Click the image to open in full size.
Click the image to open in full size.
REAR STRUT BARS F/S, PM FOR DETAILS
√ MY THREADS IN THE WHEELS/TIRES F/S SECTION
KCMAXX is offline   Send a private message to KCMAXX Find more posts by KCMAXX Add KCMAXX to Your Friends list Reply With Quote top
Old 01-31-2011, 07:40 PM   #16
my6thgen.org Profile Info.
 
Hmax's Avatar
 
Join Date: Mar 2010
Official Member #: 158
Last Online: 05-10-2018 02:35 PM
Location: Da Bronx, NY
Posts: 5,926

Reputation Level: 32
Hmax will become famous soon enoughHmax will become famous soon enough

Participation Level: 0%
Activity: 0% Activity: 0% Activity: 0%

My Awards:
Most Valuable Poster (MVP)  


/ Point Value: 10

Active Member  


/ Point Value: 5

Default Re: How to Rebuild (Z32) 300ZX Calipers

Originally Posted by KCMAXX View Post
http://www.courtesyparts.com/kb_sear...82_883_982_983


I've found some Ham, give me some time. Actually, read the post above you... lol


you know I'll share.


LMAO, i know but i want to follow up on the other thing i told you about earlier. They needed the part number. I will let you know tomorrow hahah
__________________
Originally Posted by hero782 View Post
Low & Slow!!! And I stop at potholes lol
Click the image to open in full size.

Want 12HP More?- CLICK HERE
Hmax is offline   Send a private message to Hmax Find more posts by Hmax Add Hmax to Your Friends list Reply With Quote top
Old 01-31-2011, 09:58 PM   #17
Premier Member
my6thgen.org Profile Info.
 
NiZMo1o1's Avatar
 
Join Date: May 2010
Official Member #: 211
Last Online: 10-20-2016 11:20 AM
Location: Wade County ! down in Sunny Florida
Posts: 5,222

Reputation Level: 42
NiZMo1o1 has a spectacular aura aboutNiZMo1o1 has a spectacular aura aboutNiZMo1o1 has a spectacular aura about

Participation Level: 20%
Activity: 20% Activity: 20% Activity: 20%

My Awards:
Supporting Family Member  


/ Point Value: 10

Member of the Month (M.O.T.M)  


/ Point Value: 10

Default Re: How to Rebuild (Z32) 300ZX Calipers

http://www.pdm-racing.com/products/brakesz32.html REBUILT kits here
__________________
Click the image to open in full size.
Click the image to open in full size.
R.I.P. Kevin007www.EmeraldPerformance.com
NiZMo1o1 is offline   Send a private message to NiZMo1o1 Find more posts by NiZMo1o1 Add NiZMo1o1 to Your Friends list Reply With Quote top
Reply

Tags
6th gem brake upgrade, bbk, z32 calipers

Go Back   my6thgen.org - Maxima Forum > my6thgen.org - Very Useful Information > How To's & DIY Mods > Suspension, Handling & Brakes


Currently Active Users Viewing This Thread: 1 (0 Members And 0 Guests and 1 Web Crawlers)
 
Thread Tools


All times are GMT -4. The time now is 07:54 PM.